Porsche Brake Pads and Rotors: A DIY Replacement Guide
Pads and steel rotors are a realistic DIY job on most Porsches if you respect the wear sensors, the rotor minimum thickness and the parking brake. Ceramic PCCB brakes are a different story.

In this article
- How to tell what you need: pads, rotors, or both
- Wear sensors: why they get replaced with the pads
- Rotor minimum thickness: it is printed on the rotor
- Steel brakes vs PCCB ceramic brakes
- Electric parking brakes and service mode
- The job, step by step (steel brakes)
- Bedding in new pads and rotors
- Brake fluid while you are in there
- Safety checklist
- The practical close
Brakes are one of the most satisfying jobs to do yourself on a Porsche, and one of the few where a small mistake has real consequences. On a car with steel rotors, pads and rotors are well within reach of a careful home mechanic with a torque wrench and proper stands. The details that trip people up are Porsche-specific: wear sensors that have to be replaced, rotors with a minimum thickness stamped on them, electric parking brakes that need to be put into a service position, and ceramic brakes that are a different system entirely.
This guide walks through how to tell what you actually need, the parts that are easy to get wrong, the job itself, and the bedding-in that makes new brakes work properly. The brand rule still applies: measure first, then order parts.
How to tell what you need: pads, rotors, or both
Porsche's own owner's manual language is blunt about wear: it depends to a great extent on driving style and conditions of use and cannot be expressed in actual miles on the road[2]. So go by inspection, not by mileage.
Pads. Most Porsches use pad wear sensors. According to FCP Euro, one of the sensors trips a warning once the pad has worn to a certain point, with roughly 1,000 miles of pad left depending on how you drive[6]. A Porsche 911 owner's manual says that when the wear limit is reached a warning symbol appears, and to have the pads replaced immediately[4]. Treat that warning as the deadline, not a suggestion.
Rotors. Steel rotors wear thinner with every pad set. Look for a ridge at the outer edge, deep scoring, heat cracks, or a pulsing pedal. Then measure.
Noise alone is not a diagnosis. Porsche tells its technicians that brake squeal is a normal result of different factors acting on the brake system and does not by itself constitute a defect[2]. Porsche's 2023 brake-noise bulletin has technicians check pad wear first and replace pads when they are more than 50 percent worn or damaged before chasing noise further[1].
Wear sensors: why they get replaced with the pads
A Porsche pad wear sensor is a small wired probe clipped into the pad. It trips the dash warning by wearing down along with the pad, so once it has done that job, it is used up.
- A tripped sensor will not reset. Fit new sensors with new pads, or the warning stays on.
- Even if the light never came on, parts suppliers recommend replacing sensors whenever the pads are replaced[7]. On older cars the wire and clip are often brittle, and a damaged sensor gives you a false warning later.
- Sensors are specific to model, axle and brake type. Heritage Parts Centre's 996/997 listing shows how one sensor covers some steel-brake and some PCCB applications but not others[7]. Match by VIN.
Route the sensor wire exactly as it came off, clear of the rotor and suspension travel.
Rotor minimum thickness: it is printed on the rotor
You do not have to guess when a steel rotor is done. Rotor makers stamp the minimum thickness on the part. Brembo explains that the figure is marked as MIN TH followed by the value in millimeters, that you should measure with a gauge at a minimum of four points, and that the lowest reading is the one that counts for the whole rotor[8].
- At or below MIN TH: replace it.
- Replace in pairs: Brembo says rotors must be replaced on both sides of the axle even if only one is below the minimum[8].
- Close to MIN TH: a fresh set of pads will wear it below the limit. Replace now rather than doing the job twice.
Use a proper rotor micrometer or caliper that reaches past the wear ridge. A standard caliper sitting on the ridge reads thick.
Steel brakes vs PCCB ceramic brakes
This is the most important section if you are not sure which brakes your car has.
How to tell. Porsche Ceramic Composite Brakes (PCCB) are an option on many models, and your car's option codes will confirm whether it has them. Porsche's brake bulletin lists PCCB equipment codes by model line, from the Macan (95B) and Cayenne (9YA/9YB) to the 911 (992), Panamera (971), 718 and Taycan[1].
Why PCCB is not a DIY job. Porsche treats ceramic brakes as their own system. Its service documentation has separate workshop procedures for checking and replacing PCCB pads and for the wear assessment of PCCB discs, distinct from the steel-brake procedures[1]. Ceramic rotors do not wear like steel, so a MIN TH stamp and a micrometer do not tell you whether one is serviceable. FCP Euro notes that the slightest chip or crack in a ceramic disc is grounds for immediate replacement[6]. A slip with a tool or a misjudged wear call is an expensive way to learn.
The rest of this guide assumes steel (cast-iron) rotors.
Electric parking brakes and service mode
Many newer Porsches have an electric parking brake (EPB). On those cars you cannot always just push the rear caliper piston back and swap pads. The system has to be put into a service or installation position first, usually with a diagnostic tool, and calibrated afterward.
How that works depends on the model. As one documented example, Porsche's 2023 bulletin for 2021 to 2022 718 (982) cars with PDK describes a rear parking brake that uses parking brake shoes driven by a spreader actuator. The procedure starts by moving the rear brake into its installation position with the PIWIS Tester (Parking brake, then Maintenance/repairs, then Move to installation position) before any parking brake parts are removed[3]. The same bulletin states that the PIWIS Tester's instructions take precedence over the written procedure[3].
For your car, check two things before you touch the rear brakes:
- Does it have an EPB, and is it a caliper-mounted motor or a shoe-type parking brake inside the rotor hat?
- Does your scan tool explicitly support parking brake service and calibration for your model and year?
If the answer to the second question is no, do the front axle yourself and leave the rear to someone with the right tool. Forcing a motorized caliper piston can damage the actuator. Our guide to Porsche scan tools covers which tools handle this.
The job, step by step (steel brakes)
The exact fasteners and torque values differ by model and caliper. The workflow does not.
- Prepare. Loosen the wheel bolts slightly with the car on the ground. Have new pads, sensors, any hardware the pads require, and new rotors if you measured and need them.
- Lift safely. Raise the car only at the lifting points shown in your owner's manual and support it on rated jack stands. Never work under a car held only by a jack.
- Wheel off, inspect. Look at the inner and outer pads; uneven wear can mean a sticking pad or caliper.
- Sensor out first. Unplug and remove the wear sensor before removing the pads so you do not tear the wire.
- Pads out. On fixed Porsche calipers, this typically means removing the pad retaining pins and spreader spring, then the pads.
- Push pistons back carefully. Open the reservoir cap and watch the fluid level as it rises. Do not let it overflow onto paint.
- Rotors if needed. Caliper off and supported, never hanging by the hose. Clean the hub face of rust so the new rotor sits flat. New rotors often have a protective coating; follow the maker's instructions on cleaning it off.
- Reassemble. New pads, new sensor, hardware and caliper back on. Torque the caliper bolts to the Porsche spec in the workshop information.
- Wheels on and torqued. Torque the wheel bolts to the value in your owner's manual with a calibrated torque wrench, in a cross pattern, with the car on the ground. Not with an impact gun, and not by feel.
- Pump the pedal until it is firm before the car moves an inch. The first press after pushing pistons back goes almost to the floor.
Bedding in new pads and rotors
Bedding in lays down an even transfer layer of pad material on the rotor. Porsche's own technical training explains that when pads and rotors are seated, or bedded in, material transfer from pad to rotor establishes a working coefficient of friction between the two surfaces[2].
Brembo's general guidance for new pads and discs:
- Road-test the car after replacement, and check for vibration and noise both while driving and while braking[9].
- Use brief, gradual brake applications so the pad surface aligns with the disc[9].
- Avoid extremely sharp or violent braking, which can overheat the friction material[9].
- Bedding in lasts about 300 km, roughly 190 miles[9].
If your pad maker publishes its own bedding procedure, follow it; performance and track compounds often have specific instructions. Plan the first drive on quiet roads where you can brake progressively without traffic behind you.
Brake fluid while you are in there
Pad and rotor work is a good moment to check when your brake fluid was last changed. Brake fluid absorbs moisture over time, which lowers its boiling point. Porsche's interval is time-based on the models we checked: a Porsche dealer's Macan schedule lists a brake fluid change every 2 years[10], and FCP Euro reports the same 2-year interval for the 997[6]. Confirm the interval and fluid specification for your car in our Porsche maintenance schedule guide or your maintenance booklet.
Safety checklist
- Lift only at the designated points, and use jack stands rated for the car.
- Chock the wheels that stay on the ground.
- Never let a caliper hang by its brake hose.
- Keep brake fluid off paint and out of your eyes; it damages both.
- Torque caliper bolts and wheel bolts to Porsche's specs, and recheck wheel bolt torque after the first short drive.
- Confirm a firm pedal before moving the car, and test the brakes at walking pace first.
The practical close
On a steel-brake Porsche, a pad and rotor job comes down to a few disciplines: measure against the MIN TH stamp, replace sensors with the pads, respect the parking brake service mode on cars that have one, torque everything to spec, and bed the new parts in gently. If your car has PCCB, or your scan tool cannot handle the rear parking brake, split the job and let a specialist take that part.
The TekGarage app keeps your brake service, fluid dates and costs in one history alongside Porsche-specific intervals, so the next pad job is a planned one. And if the car pulls, pulsates or keeps a warning after the job, Tomorrow'sTek support can help you work out why before you buy more parts.
Sources
- Technical Information 122/20: Complaint - Brake Noises: Classifying Features and ProcedureCovers Macan (95B), Panamera (971), 718 (982), 911 (992), Cayenne (9YA/9YB) and Taycan, as of model year 2017.
- Advanced Technical Information 1605: Brake SquealApplies to all vehicle types. Quotes the owner's manual section on brake pads and discs.
- Technical Information 166/22: WNK6 - Replacing Spreader Device (Actuator) (Workshop Campaign)Applies to 718 (982) with PDK, model years 2021 to 2022.
- Porsche 911 Carrera owner's manual, brake pads and brake discs pageHosted copy of a Porsche owner's manual; the page does not state the model year.
- Porsche Ceramic Composite Brake (PCCB) brochure, page 43Hosted copy of a Porsche PCCB brochure for the 911 Carrera 4; model year not stated.
- The Definitive Guide To The Porsche 997 Brakes
- Brake Pad Wear Indicator, Front or Rear: 996 (2004-2005), 997 (2005-2012)
- Minimum brake rotor thickness
- Indications and bedding in
- Porsche Macan Maintenance SchedulePublication date not shown.
Diagnose first. Then turn the bolt.
Get help before the next bolt
Members get repair guidance, specs and a second set of eyes on the job.


